Tools Popular is reader-supported. When you buy via links on our site, we may earn an affiliate commission at no cost to you. Learn more.

How to Start a Husqvarna Chainsaw – Best Easiest Way is Here!

How to Start a Husqvarna Chainsaw

It can be quite a challenge to launch or start a chainsaw properly. Like so many chainsaw models, Husqvarna chainsaws even have their own style and unique way to start.

This two-cycle chainsaw’s gas tank can easily startup if sufficient gas, air, and spark are present. However, getting the right combination of these three might be a challenge. Since if the proportions are not correct, the Husqvarna chainsaw won’t start!

Therefore, you must know all its ins and outs when trying to start the Husqvarna chainsaw.

So, how do you get along to start a Husqvarna chainsaw?

This is where this blog post will come in handy, so keep reading till the end to know all.

How to Start a Husqvarna Chainsaw? : All You Need to Know

Before starting any type of power chainsaw, it is essential to know about safety. When you have taken all the precautions, you will begin by opening your Husqvarna chainsaw fuel cap.

After that, you can pour the engine oil into the authorized fuel container and then add the right quality gasoline until it is filled. Pour the combined gasoline into the Husqvarna chainsaw’s fuel tank, and reseal it.

Next, you have to push the chain brake to the front handguard on the engine’s top and locate your chainsaw’s choke lever. You will notice that this choke lever will be located close to the chainsaw’s rear handle.

You will have to put the choke lever to a “half-opened” position. To purge the system of air, press the air-purge switch until it’s filled with gasoline.

This button is located beside or near the starter rope. Then, adjacent to the cylinder, you must have to push the decompression valve.

After completing all of the preceding procedures, put the chainsaw on the ground, and then place your left hand on top of the front handle, and slide your right foot into the back handle.

Once everything is in place, you will use your dominant hand to pull the chainsaw’s starter cord. Do not twist the rope on your hand and pull it forcefully to start the cold engine. Instead, press the choke lever to the “closed” position as soon as the engine starts.

Then pull the chainsaw’s starter rope repeatedly until the chainsaw begins to run. You should keep squeezing the trigger lock and the throttle together after picking up the chainsaw from the ground to disengage the clutch and prevent wear on the clutch.

Then, when you’re ready to cut, release the chain brake. Always make sure that when you are using the chain brake you need to be extra careful as it determines the safety of your chainsaw. And also focus on the recoil assembly for your chainsaws to stay durable.

Obviously, doing the following in the wrong way will result in disappointing outcomes, so learn it well.

The points below will explain how you can start your Husqvarna chainsaw.

1. Remove the bar cover from the chainsaw and place it on a flat surface.
2. To ensure safety, push the chain brake on the top handle forward. Always remember that the chain brake is very important for you to have better control of your chainsaw. Even chain brake engaged can create issues while starting your Husqvarna chainsaw.
3 Push in control of the Husqvarna smart start.
4. To easily view the gasoline level, press the fuel pump.
5. With your hands, pull the starter handle and then use your right foot on the front handle to pull the starter rope and your left hand to hold the saw and grab the chain with your right hand.
6. Halfway down the throttle and pull the starter cord until the chainsaw starts.

These are the primary applications that you need to follow for accurate and proper engine fires of your chainsaw.

Common Issues that You Might Face with Husqvarna Chainsaws.

In this section of the article, you’ll look at some of the common problems that you might encounter with Husqvarna chainsaws.

So keep reading till the end to know all the solutions to these problems.

Clogged Filters

When the fuel filter is dirty, they pull more gas than air, comparable to when the choke control is engaged. When a chainsaw is operated in this condition, carbon deposits are increased caused by the formation of unburned fuel. When the previously run engine is inactive, the carbon buildup may deteriorate.

To avoid such issues, clean your fuel filter after each usage. So that there is no leaving fuel or clogged fuel that might damage your engine.

Clogged Carburetor

Do not fill the chainsaw’s gasoline tank unless it is running. Otherwise, if the sticky fuel is left in the tank for too long, it will clog the carburetor. The carburetor run needs to be smooth for the chainsaw to run fine and for a long period of time.

When it happens, the fuel’s light particles evaporate, leaving a thick mixture behind. This explains why the Husqvarna chainsaw is not receiving fuel.

If the clogging jets are already clogged, carefully clean them with a specialized carburetor cleaner to remove the sticky and excess fuel.

Clean the chainsaw as well if it is coated in heavy, sticky substances. If cleaning the carburetor does not resolve the issue, try completely replacing it.

Flooded Engine

When starting a chainsaw, you need to squeeze the fuel primer bulb for an easier start. However, overdoing it may cause the engine to overflow and become unable to run. So, it’s essential that you are extra careful with the chainsaw engine.

A sure sign of this situation is the scent of gasoline flowing from your chainsaw. To avoid this from happening, try removing your spark plug and inspecting it for dampness.

The most effective technique to resolve this issue is opening the spark plug and draining the tank’s petrol. Firmly pull the starter cord and deactivate the choke position while briefly pushing the throttle. Dry the spark plug and replace it in its proper location.

Examine The Fuel Tank

This may appear strange, but it is possible while attempting to determine why your chainsaw is not working. You may have forgotten to refill the gasoline tank, or the fuel may be contaminated.

In most cases, bad fuel is left over after the chemical components of the gasoline have evaporated and degraded. And sometimes, extreme logging can also resist the chainsaw from working properly.

If the fuel is contaminated, drain the tank and refuel with fresh, clean gas. You also need to make sure that the fuel mixture is compatible with your engine. Avoid combining ethane and methane in gasoline blends as they are harmful to the engine.

Bottom Line

Starting the Husqvarna chainsaw might be quite a challenge if you don’t know the right ins and outs. Although each of the versions and models varies, so always check the model number and the serial number of your chainsaw and use it accordingly.

However, with the help of this article, you’ll know all the necessary information to use the Husqvarna chainsaw, no matter what versions or models you use. Even for the largest chainsaw of Husqvarna, you can use these guidelines for starting your chainsaw. 

Although, you need to make sure that you handle it with proper care whenever you use this chainsaw and follow the operator’s manual for better and enhanced performance. Ready to buy a Husqvarna? Read our review on the Best 20-inch Chainsaw!

LEAVE A REPLY

Please enter your comment!
Please enter your name here

Read More

Recent